Shure PSM900 Specifications download pdf (Page 6)

Rack Unit Transmitter

Front Panel Controls

① Input Level Control and Display

Usethe▼▲buttonstoadjusttheaudiosothat,fortheaverageinputsignallevel,

the top two yellow LEDs flicker and the lower LEDs are solid. The red clip LED

indicates the inputs are overdriven. Reduce the level at the audio source or

change the input sensitivity of the rack unit from the AUDIO > INPUT menu.

② Status Display and Menu Controls

Use the enter and exit buttons and the menu wheel to access the configuration

menu. Push the menu wheel to move the cursor to the next item. Turn the menu

wheeltochangeaparameter—theenter button flashes. Press it to save the

value. Press the exit button to cancel changes and return to the previous menu.

③ Synchronization Button

Press the sync button while rack unit and bodypack IR windows are aligned to

transfer settings.

④ Headphone Monitoring

The volume control adjusts signal output to the 3.5 mm headphone jack. NOTE:

it does not affect rear panel outputs.

⑤ RF switch

Mutes RF output. For setting up multiple systems or adjusting settings without

transmitting unwanted RF or audio signals.

⑥ Power Button

Turns the unit on and off.

Rear Panel Connectors

⑦ Power

Connect the transmitter to a power outlet using the supplied power adapter.

⑧ LOOP OUT

Sends a copy of the audio signal going into the transmitter to another de-

vice. See LOOP Applications.

⑨ Audio Inputs

Connect to balanced or unbalanced outputs. Use either connector for mono

input. Accepts both 1/4-inch or male XLR connectors.

⑩ Antenna (BNC)

Attach supplied antenna. If you are rack mounting, use a front panel or re-

mote mounting kit from Shure.

level L R menu sync volume power

CLIP

sync

Configuration Menu

Note: Configuration menu items may vary with regional model variations.

Audio Settings

AUDIO > MODE

Selects monitor mode

STEREO/MX

Transmits both channels

MONO

Transmits a mono signal to

bodypack

AUDIO > INPUT

Sets nominal input level

LINE +4 dBu

line level

AUX -10dBV

aux level

RF Settings

RADIO

Sets the group number

Sets the channel number

888.888MHz

Manual frequency selection

RF POWER

Select from 10, 50, or 100 mW

(varies by region)

Utilities and Display Settings

UTILITIES

EDIT NAME

Changes the name on the LCD display (this name

is uploaded to the bodypack with sync)

DISPLAY

Changes the display format

CONTRAST

Changes the display contrast

CUSTOM GROUP

For creating custom frequency groups

UTILITIES > LOCK PANEL

Locks front panel controls. To unlock, press exit, select

OFF, and press enter.

MENU+LEVEL

Locks menu and level controls.

MENU ONLY

Locks only the configuration menu (menu controls).

MENU+SWITCH

Locks all controls except for the level buttons (in-

cluding the RF and power switches).*

ALL

Locks all controls (including the RF and power

switches).*

*RF is automatically activated when locked. When you

unlock the unit, RF and power turns off if the swithes

are off.

UTILITIES > RX SETUP

These settings are sent to the bodypack during a sync (when the sync

direction is from the transmitter). The default KEEP parameter will not

change the bodypack settings.

LOCK

Lock bodypack

V LIMIT

Volume limiter

LIM VAL

Volume limiter value

MODE

Stereo (ST) or MixMode (MX)

BAL MX

CH. 1 (L) and CH. 2 (R) mix for MixMode

BAL ST

Left (L) and right (R) balance for stereo mode

HIBOOST

high frequency boost

UTILITIES > RESET SYSTEM

Returns all settings to the factory defaults

Exit and do not reset system.

YES

Reset system settings.

1 2 3 4 5 6 7 8 9 10 11 12 13 14

Comments to this Manuals

No comments

Shure PSM900 Specifications Page 6

Comments to this Manuals

Related products and manuals for Microphones Shure PSM900