Shure Performance Gear Specifications download pdf (Page 2)

Issue LED Status Solution

No sound or

faint sound

Transmitter Power/

Mute LED on,

receiver LEDs on

• Perform transmitter setup.

• Verify all sound system connections.

• Adjust transmitter gain.

Receiver Channel

Display off

• Make sure AC adapter is securely

plugged into electrical outlet and into

POWER connector on rear panel of

receiver.

• Make sure AC electrical outlet works

and is supplying proper voltage.

Transmitter LED

glowing

or ashing red

• Replace transmitter battery.

Transmitter LED off • Turn transmitter on.

• Make sure the +/– indicators on battery

match transmitter terminals.

• Insert fresh battery.

Distortion or unwanted noise bursts • Remove nearby sources of RF

interference (CD players, computers,

cell phones, digital effects, in-ear

monitor systems, etc.)

• Select a new channel for both receiver

and transmitter.

• Reduce transmitter gain.

• Replace transmitter battery.

• If using multiple systems, change the

channel of one of the active systems.

Sound level different from cabled

guitar or microphone, or when using

different guitars

• Adjust transmitter gain as necessary.

Cannot turn

transmitter on

Transmitter LED

ashing red

• Replace transmitter battery.

Troubleshooting

Regulatory Information

Replacement Parts

Technical Specications

Audio Input Level –10 dBV maximum at “mic” gain position

+10 dBV maximum at 0dB gain position

+20 dBV maximum at –10dB gain position

Gain Adjustment Range 30 dB

Input Impedance 1mΩ

RF Transmitter Output 10 mW typical (dependent on applicable country regulations)

Dimensions 110 mm H x 64 mm W x 21 mm D (4.3 x 2.5 x 0.8 in.)

Weight 75 grams (2.6 oz.) without battery

Housing Molded ABS

Power Requirements One 9V alkaline or rechargeable battery

Battery Life Up to 8 hours (alkaline)*

Working Range 75m (250 ft.) Note: actual range depends on RF signal absorption, reection,

and interference.

Audio Channel Response Minimum: 45 Hz.

Maximum: 15 kHz (overall system channel depends on

microphone element).

Total Harmonic Distortion 0.5%, typical

Ref. +/– 33 kHz deviation, 1 kHz tone

Dynamic Range >100 dB A-weighted, typical

Operating Temperature

Range

–18°C (0°F) to +57°C (+135°F)

Note: battery characteristics may limit this range

Transmitter Audio Polarity Positive pressure on microphone diaphragm (or positive voltage to tip of WA302

phone plug) produces positive voltage on pin 2 (with respect to pin 3 of low

impedance output) and the tip of the high impedance 1/4-inch output.

Audio Input Level +2 dBV maximum at –10dB position

–8 dBV maximum at 0dB position

Gain Adjustment Range 10dB

RF Transmitter Output 10 mW typical (dependent on applicable country regulations)

Dimensions 223.52 L x 53.34 Dia. (8.8 in. x 2.10 in.)

Weight 218 grams (7.7 oz.) without battery

Housing Molded ABS handle and battery cup

Power Requirements One 9V alkaline or rechargeable battery

Battery Life Up to 8 hours (alkaline)*

Output Impedance XLR connector: 200 Ω 1/4 inch connector: 1kΩ

Audio Output Level Ref. +/–

33 kHz deviation with

1 kHz tone

XLR connector (into 100K Ω load): –19 dBV, typical

1/4 inch connector (into 100K Ω load): –5 dBV, typical

Sensitivity –105 dBm for 12 dB SINAD, typical

Image Rejection >50 dB, typical

Dimensions 188 mm L x 103 mm W x 40 mm D (7.4 in. x 4.0 in. x 1.5 in.)

Dimensions - PG88 388 mm L x 116 mm W x 40 mm D (15.3 in. x 4 in. x 1.5 in.)

Weight 241 grams (8.5 oz)

Weight - PG88 429 grams (15.1 oz)

Housing Molded ABS

Power Requirements 12–18 Vdc at 160 mA (PG4), 320mA (PG88), supplied by external

power supply

System

PG1 Bodypack Transmitter

PG2 Handheld Transmitter

Regulatory Information for North America, Europe, and Australia

PG1 & PG2 Transmitters: Certied to FCC Part 74 (FCC ID: “DD4PG1” and “DD4PG2”).

Certied by IC in Canada under RSS-123 and RSS-102 (“IC: 616A-PG1” and “IC: 616A-

PG2”). Meets the essential requirements of the European R&TTE Directive 99/5/EC (ETSI EN

300-422 Parts 1 & 2, EN 301 489 Parts 1 & 9) and are eligible to carry the CE marking.

PG4 and PG88 Receiver: Authorized under Declaration of Conformity (DoC) provision of

FCC Part 15. Certied under Industry Canada to RSS-123 (“IC: 616A-PG4”). This class B

digital apparatus complies with Canadian ICES-003. Meets the essential requirements of the

European R&TTE Directive 99/5/ EC (EN 301 489 Parts 1 & 9, EN 300 422 Parts 1 & 2) and

is eligible to carry the CE marking. Conforms to Australian EMC requirements and is eligible

for C-Tick marking.

NOTE: This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This equipment

generates, uses and can radiate radio channel energy and, if not installed and used in

accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If

this equipment does cause harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

-- Reorient or relocate the receiving antenna.

-- Increase the separation between the equipment and receiver.

-- Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

-- Consult the dealer or an experienced radio/TV technician for help.

PS21 Series Power Supplies: Conform to Safety Standard IEC 60065.

PS21E and PS21UK are eligible to bear CE marking.

N108

0978

Technical Specications cont’d

PG4 and PG88 Receiver

SHURE Incorporated http://www.shure.com

United States, Canada, Latin America, Caribbean:

5800 W. Touhy Avenue, Niles, IL 60714-4608, U.S.A.

Phone: 847-600-2000 U.S. Fax: 847-600-1212 Int’l Fax: 847-600-6446

Europe, Middle East, Africa:

Shure Europe GmbH, Phone: 49-7131-72140 Fax: 49-7131-721414

Asia, Pacic:

Shure Asia Limited, Phone: 852-2893-4290 Fax: 852-2893-4055

Changes or modications not expressly approved by Shure Incorporated for compliance could

void the user’s authority to operate the equipment. Operation of this device is subject to the

following two conditions: (1) this device may not cause interference, and (2) this device must

accept any interference, including interference that may cause undesired operation of the

device.

Caution

System Components

All Systems

PG4 or PG88 Receiver

Internal Diversity Antenna System

One 9 volt battery AC Power supply User guide

Vocalist System

Microphone Head PG2 handheld transmitter Microphone clip

Instrument System

PG1 bodypack

transmitter

4-pin mini connector (TA4F) to

1/4” connector cable

Lavalier and Headworn System

PG1 bodypack

transmitter

Microphone (choice of PG185, PG30)

Patents

Patent numbers 6,597,301, 6,296,565, 7,414,587, D536,692 and D535,974

All Systems Microphone Stand Adapter (PGX2) WA371

System-Specic AC Adapter (120 VAC, 60 Hz) PS21

AC Adapter (220 VAC, 50 Hz), Argentina PS21AR

AC Adapter (230 VAC, 50/60 Hz, Europlug) PS21E

AC Adapter (230 VAC, 50/60 Hz, UK) PS21UK

AC Adapter (100 VAC, 50/60 Hz) PS21J

AC Adapter (220 VAC, 50 Hz, China) PS21CHN

AC Adapter (230 VAC, 50 Hz,, Australia) PS21AZ

AC Adapter (220 VAC, 60 Hz, Korea PS21K

PG58 Head with Grille RPW108

Belt Clip 44A8035

Optional Universal Rack Tray URT

4-pin mini connector (TA4F) to 1/4”

connector cable

WA302

A ministerial license may be required to operate this equipment in certain areas. Consult your

national authority for possible requirements.

This radio equipment is intended for use in musical professional entertainment and similar

applications.

To set up multiple systems, repeat the previous steps for each transmitter and

receiver pair. Once transmitters have been set, leave them on. Be sure to set

each transmitter and receiver pair to a different channel. For information about

frequencies and compatibility, refer to channel guide.

Multiple System Setup

Wearing the Bodypack Transmitter

Clip the transmitter to belt or

guitar strap as shown.

Make sure the antenna is

unobstructed.

Changing Battery

Expected life for a 9 volt alkaline battery is up to 8 hours.

Total battery life will vary depending upon battery type and

manufacturer.

Red LED signifies “low battery” with typically less than 60 minutes

of remaining battery life.

Note: Remaining battery life will vary depending upon battery

type and manufacturer.

* See “Changing Battery”

1 2

Comments to this Manuals

No comments

Shure Performance Gear Specifications Page 2

Comments to this Manuals

Related products and manuals for Microphones Shure Performance Gear